Questions? +32 460 226 991 (English). EU-wide delivery!

Refrigerant detector EVIKON E2608-HFC for air ducts

Refrigerant detector EVIKON E2608-HFC for air ducts

EVIKON
  • Product code: E2608-HFC-DM
  • Manufacturer code: E2608-HFC-DM
  • Warranty: 2 years

Refrigerants detector Evikon E2608-HFC with two relays with switch-over contact, RS485 Modbus RTU digital interface and two analog outputs settable to 4-20 mA or 0-10 V. Industrial IP65 housing. Power supply 230V. More information

  • Availability

    Out of stock - can be requested

  • Out of stock  
Price without VAT € 350,92
Price with VAT 21 % € 424,61
+

Would you like to get a price offer? Contact us

Parameters and catalogs

Detector type To VZT cannal
Output signal ModBus RS485, 2x Switching relay, 2x Analog output 4-20mA/0-10V
Power 24 VDC, 230 VAC
Type of gas HFC-Refrigerants
Weight 0.44 kg

Datasheet download

Download PDF

Assembly instructions download

Download PDF

DECLARATION OF CONFORMITY download

Download PDF

Refrigerant detector is used to detect and warn early of a dangerous (toxic) concentration of the refrigerant being sensed. It is important to detect leakage of previously used chlorofluorocarbons (CFCs) and of today's HFCs. The leakage of these gases has a negative impact on the environment and the formation of the ozone layer. In the event of leakage, refrigerant may also accumulate in enclosed spaces up to toxic levels. It is therefore necessary to provide early warning of leakage using a detector.


Hydrocarbon refrigerants tend to decline because they are heavier than air. Refrigerant detectors should therefore be mounted to the floor near a potential leak location. The recommended coverage area of one detector is 80 ... 120m2, which corresponds to a radius of about 5 ... 6m.
Refrigerant detectors are widely used, ranging from kitchens and restaurants to cold stores, warehouses, supermarkets, skating rinks and food industry factories.

The EVIKON E2608-HFC detector is equipped with two-stage signaling with outputs to the switching relay. It does not have its own visual and acoustic signaling. The E2608 series detectors are an intelligent solution for modern applications with ModBus RS485 communication and two 4-20mA/0-10V analog outputs.

The detector can be ordered in the following versions:

  • wall-mount (in stock)
  • duct-mount (on request)
  • with cable probe (on request)

Made in robust design with IP65 protection - ABS plastic, resistant to mechanical damage. Rigid, tough, resistant to low and high temperatures, poorly absorbent, harmless to health. The service life of the detector is more than 10 years.

Each detector is factory calibrated to the default values (described in the manual). The law states that recalibration must be performed at least once every 12 months. Calibration may only be performed by a person certified by the manufacturer.

Do not hesitate to contact us for recalibration!

The detector is designed to detect refrigerants:

R-12, R-123, R-125, R-134a, R-143, R-22, R-404a, R-407c, R-410a, etc.

Features:

  • Selective, sensitive and stable detection
  • Metal oxide NDIR on demand sensor
  • Wall, duct mounting, remote probe, IP65 protection
  • Two relays for alarm/ventilation control
  • Two analog outputs settable to 4-20 mA or 0-10 V
  • RS485 Modbus RTU digital interface

Tip: Get notified by the service about the date of legal calibration www.kalibrovat.cz

We respond to your product queries as quickly as possible, usually within 24 hours.

Didn't find what you wanted to know?